Home
Instruction manual
Starting up and operating devices of the Digital 6000 line.
SK 6212 bodypack transmitter
These sections contain information about installing, starting up and operating the SK 6212 bodypack transmitter.
Operating the menu of the SK 6212 bodypack transmitter
Navigating through the menu and making changes.
Lock menu item
In this menu item, you can activate or deactivate the lock-off for the transmitter.

Instruction manual
Starting up and operating devices of the Digital 6000 line.
- EM 6000 2-channel receiver
  These sections contain information about installing, starting up and operating the EM 6000 2-channel receiver.
- SKM 6000 handheld transmitter
  These sections contain information about installing, starting up and operating the SKM 6000 handheld transmitter.
- SK 6000 bodypack transmitter
  These sections contain information about installing, starting up and operating the SK 6000 bodypack transmitter.
- SK 6212 bodypack transmitter
  These sections contain information about installing, starting up and operating the SK 6212 bodypack transmitter.
  - Product overview
  - Inserting and removing the BA 62 rechargeable battery
  - Mounting the antenna
  - Connecting a microphone to the SK 6212 bodypack transmitter
  - Connecting an instrument or line source to the SK 6212 bodypack transmitter
    You can connect instruments or audio sources with a line level to the SK 6212 bodypack transmitter.
  - Switching the SK 6212 on and off
  - Home screen
  - Displays on the SK 6212 bodypack transmitter display panel
    You can view the following information on the transmitter display.
  - Operating the menu of the SK 6212 bodypack transmitter
    Navigating through the menu and making changes.
    - Frequency menu item
      In this menu item, you can adjust a frequency in 25 kHz steps.
    - Name menu item
      In this menu item, you can set a freely selectable name for the transmitter.
    - Gain menu item
      In this menu item, you can adjust the input gain in 3 dB steps.
    - Low Cut menu item
      In this menu item, you can adjust the value for the low cut filter.
    - Display menu item
    - Lock menu item
      In this menu item, you can activate or deactivate the lock-off for the transmitter.
    - Test Tone menu item
      In this menu item, you can activate a 1 kHz test tone that the transmitter transmits instead of the input signal.
    - Power LED menu item
      In this menu item, you can set the behavior of the LED above the SK 6212’s display and the ON/OFF button.
    - RF Power menu item
      In this menu item, you can set the transmission power of LR mode in two steps:
    - Reset menu item
      In this menu item, you can reset the transmitter settings to the factory settings.
    - Information menu item
      In this menu item, you can display the installed firmware version and the overall frequency range for the transmitter.
  - Updating the transmitter firmware
- Modular L 6000 charger
  These sections contain information about installing, starting up and operating the modular L 6000 charger and the corresponding charging modules.
- L 70 USB charger
- Establishing a radio link
  Note the following points when you establish a radio link between the transmitter and receiver.
- Synchronizing devices
- Cleaning and maintenance
  Note the following information when cleaning and maintaining Digital 6000 series products.

Lock menu item

In this menu item, you can activate or deactivate the lock-off for the transmitter.

Alternatively, you can also adjust the lock-off in the receiver and synchronize it with the transmitter. See Sync Settings menu item.

To enable the lock-off:

Open the Lock menu item and set the value to On.
Save your entry by pressing the SET button.
The automatic lock-off function will remain activated.
The display switches off.

To temporarily deactivate the lock function:

Press the ON/OFF/ESC button.
The display is reactivated.
Press the ON/OFF/ESC button again.
The message LOCKED is shown on the display.
Press the UP or DOWN button.
The message UNLOCK is shown on the display.
Press the SET button.
The lock-off function is now temporarily disabled.
You can change settings as needed in the menu. The lock-off function is reactivated after 10 seconds of inactivity.

To completely deactivate the lock-off function:

Open the Lock menu item and set the value to Off.
Save your entry by pressing the SET button.
The automatic lock-off function will remain disabled.