Home
Instruction manual
Detailed description of the start-up and operation of the hardware and the WebUI.
WebUI
Detailed description of the WebUI navigation and configuration.
Configuration
Under Configuration, you can set the essential settings for the RF channel, antenna, Base Station and mobile devices.
Mobile Devices
Here you can configure specific settings for mobile devices.
Activating/deactivating cable emulation
You can emulate the capacitance of the connected instrument cable and influence the sound of your mic/line input.

Instruction manual
Detailed description of the start-up and operation of the hardware and the WebUI.
- Base Station
- WebUI
  Detailed description of the WebUI navigation and configuration.
  - Getting started
    Start your basic configuration with the recommended steps.
  - Configuration
    Under Configuration, you can set the essential settings for the RF channel, antenna, Base Station and mobile devices.
    - General settings
      Overview of the general settings and messages.
    - RF configuration
      Here you can set up your RF channel and check the status of local permissions, your connected antenna, and any potential frequency interference in the surrounding area.
    - Base Station
      Here, you can check the basic settings of the Base Station and easily perform tasks such as firmware updates, walk tests, or restoring it to factory settings.
    - Audio interfaces
      Here you can monitor all available interfaces and manage the outputs.
    - Mobile Device Monitoring
      Here you can monitor the live data of the mobile devices as graphs.
    - Mobile Devices
      Here you can configure specific settings for mobile devices.
      - Pairing/unpairing mobile devices
        In the WebUI, you can pair up to 128 mobile devices to a Base Station within one RF channel.
      - Identifying your mobile device
        You can remotely identify your mobile device.
      - Assigning an RF channel
        You can assign a configured RF channel to your mobile device.
      - Selecting audio link mode (IEM)
        You can select the audio mode for your IEM link.
      - Selecting audio link mode (Mic/Line)
        You can select the audio mode for your Mic/Line link.
      - Selecting the Mic/Line input
        You can select the audio input as the signal source for your Mic/Line link.
      - Adding/removing an audio channel (Mic/Line)
        You can assign an audio channel number and the interface output for your Mic/Line link.
      - Changing the device name
        You can change the device name for your mobile device.
      - Changing the LED color
        You can select the connected state color of your LED on the mobile device.
      - Selecting the IEM audio interface
        You can select the desired audio interface as the signal source for your IEM link.
      - Selecting an audio channel (IEM link)
        You can assign an audio channel number for your IEM link.
      - Adjusting the balance
        You can change the balance for your IEM link.
      - Setting the volume
        The volume can be controlled directly from the device as well as from the WebUI.
      - Setting the min volume
        You can set a predefined min volume for your IEM link.
      - Setting the max volume
        You can set a predefined max volume for your IEM link.
      - Selecting the phones output
        Selecting the output for the PHONES socket of the mobile device.
      - Activating/deactivating cable emulation
        You can emulate the capacitance of the connected instrument cable and influence the sound of your mic/line input.
      - Activating/deactivating Low Cut
        You can reduce or remove low frequencies in the audio signal while allowing high frequencies to pass through.
      - Setting the Preamp Gain
        With the preamp you can increase the audio level for your Mic/Line output.
      - Activating/deactivating Test Tone
        With a constant test tone, you can simulate and test the performance of your audio devices in different dB levels.
      - Setting the command mode
        You can set the command mode for the COM button.
  - Frequency Scan
    You can use an RF scan to examine the current frequency situation of your connected antenna.
  - Audio Metering
    Under Audio Metering you can monitor all interfaces at a glance.
  - Audio inputs and outputs
    Here you have an overview of all channels at a glance and can assign the audio network input and output for the link channels directly and easily.
  - Changing the device password
    You have two options to change the device password on your Base Station.
- SEK
- SKM
- DAD
- CHG 70N-C charger
  The CHG 70N-C is a network enabled charger featuring two individual charging bays.
- L 70 USB charger
- Modular L 6000 charger
  These sections contain information about installing, starting up and operating the modular L 6000 charger and the corresponding charging modules.
- Cleaning and maintenance
  Note the following information when cleaning and maintaining products of the Spectera series.

Activating/deactivating cable emulation

You can emulate the capacitance of the connected instrument cable and influence the sound of your mic/line input.

Cable emulation is only applicable when line input is selected.

The following presets are available:

OFF
Short
Mid
Long

To activate cable emulation:

In the top bar, navigate to Configuration > Mobile Devices > Mic Settings.
Select the value Line from the audio input list.
Select the value from the drop-down list Cable Emulation.

To deactivate cable emulation:

Select the value OFF.

The cable emulation value has been activated/deactivated.