Home
User manual
Detailed description of the start-up and operation of your selected hardware and software product.
WebUI
Detailed description of the WebUI navigation and configuration.
Configuration
Under Configuration, you can set the essential settings for the RF channel, antenna, Base Station and mobile devices.
Mobile Devices
Here you can configure specific settings for mobile devices.
Changing the device name
You can change the device name for your mobile device.

User manual
Detailed description of the start-up and operation of your selected hardware and software product.
- Spectera
  Detailed description of the start-up and operation of your selected hardware.
- WebUI
  Detailed description of the WebUI navigation and configuration.
  - Get started
    Starting the WebUI for the first time, including device authentication and license entitlement.
  - Resetting the device password
    You can reset the assigned device password on your Base Station to its factory settings.
  - Basic configuration
    Start your basic configuration with the recommended steps.
  - Configuration
    Under Configuration, you can set the essential settings for the RF channel, antenna, Base Station and mobile devices.
    - RF configuration
      Here you can set up your RF channel and check the status of local permissions, your connected antenna, and any potential frequency interference in the surrounding area.
    - Base Station
      Here, you can check the basic settings of the Base Station and easily perform tasks such as firmware updates, walk tests, or restoring it to factory settings.
    - Audio interfaces
      Here you can monitor all available interfaces and manage the outputs.
    - Mobile Devices
      Here you can configure specific settings for mobile devices.
      - Pairing/unpairing mobile devices
        In the WebUI, you can pair up to 128 mobile devices to a Base Station within one RF channel.
      - Identifying your mobile device
        You can remotely identify your mobile device.
      - Assigning an RF channel
        You can assign a configured RF channel to your mobile device.
      - Selecting audio link mode (IEM)
        You can select the audio mode for your IEM link.
      - Selecting audio link mode (Mic/Line)
        You can select the audio mode for your Mic/Line link.
      - Selecting the Mic/Line input
        You can select the audio input as the signal source for your Mic/Line link.
      - Adding/removing an audio channel (Mic/Line)
        You can assign an audio channel number and the interface output for your Mic/Line link.
      - Performing a walk test
        A walk test allows you to check the reception quality of your radio links within the operating environment.
      - Changing the device name
        You can change the device name for your mobile device.
      - Setting the LED brightness
        You can adjust the brightness of your LED on the mobile device.
      - Selecting the IEM audio interface
        You can select the desired audio interface as the signal source for your IEM link.
      - Selecting an audio channel (IEM link)
        You can assign an audio channel number for your IEM link.
      - Activating Focus mode
        You can activate/deactivate Focus mode for your IEM link.
      - Adjusting the balance
        You can change the balance for your IEM link.
      - Setting the volume
        The volume can be controlled directly from the device as well as from the WebUI.
      - Setting the min volume
        You can set a predefined min volume for your IEM link.
      - Setting the max volume
        You can set a predefined max volume for your IEM link.
      - Activating/deactivating cable emulation
        You can emulate the capacitance of connected cables and influence the sound of your mic/line input.
      - Activating/deactivating Low Cut
        You can reduce or remove low frequencies in the audio signal while allowing high frequencies to pass through.
      - Setting the Preamp Gain
        With the preamp you can increase the audio level for your Mic/Line output.
      - Activating/deactivating Test Tone
        With a constant test tone, you can simulate and test the performance of your audio devices in different dB levels.
    - Activating the license
      Under Entitlement, you can enter and activate the current license for the frequency spectrum.
  - Frequency Scan
    You can use an RF scan to examine the current frequency situation of your connected antenna.
  - Audio levels
    Under Audio Levels you can monitor all interfaces at a glance.
  - Audio inputs and outputs
    Here you have an overview of all channels at a glance and can assign the audio network input and output for the link channels directly and easily.
- LinkDesk
  Detailed description of the installation, start-up and operation of the LinkDesk software.

Changing the device name

You can change the device name for your mobile device.

For security reasons, please do not enter any sensitive personal data as the device name.

To change the device name:

In the top bar, navigate to Configuration > Mobile Devices.
Edit the name under Name and confirm with ENTER.
The name is immediately transmitted to the mobile device and saved.

The device name has been changed.