User manual
Detailed description of the start-up and operation of your selected hardware and software product.
- Spectera
  Detailed description of the start-up and operation of your selected hardware.
- WebUI
  Detailed description of the WebUI navigation and configuration.
  - Get started
    Starting the WebUI for the first time, including device authentication and license entitlement.
  - Resetting the device password
    You can reset the assigned device password on your Base Station to its factory settings.
  - Basic configuration
    Start your basic configuration with the recommended steps.
  - Configuration
    Under Configuration, you can set the essential settings for the RF channel, antenna, Base Station and mobile devices.
    - RF configuration
      Here you can set up your RF channel and check the status of local permissions, your connected antenna, and any potential frequency interference in the surrounding area.
    - Base Station
      Here, you can check the basic settings of the Base Station and easily perform tasks such as firmware updates, walk tests, or restoring it to factory settings.
    - Audio interfaces
      Here you can monitor all available interfaces and manage the outputs.
    - Mobile Devices
      Here you can configure specific settings for mobile devices.
      - Pairing/unpairing mobile devices
        In the WebUI, you can pair up to 128 mobile devices to a Base Station within one RF channel.
      - Identifying your mobile device
        You can remotely identify your mobile device.
      - Assigning an RF channel
        You can assign a configured RF channel to your mobile device.
      - Selecting audio link mode (IEM)
        You can select the audio mode for your IEM link.
      - Selecting audio link mode (Mic/Line)
        You can select the audio mode for your Mic/Line link.
      - Selecting the Mic/Line input
        You can select the audio input as the signal source for your Mic/Line link.
      - Adding/removing an audio channel (Mic/Line)
        You can assign an audio channel number and the interface output for your Mic/Line link.
      - Performing a walk test
        A walk test allows you to check the reception quality of your radio links within the operating environment.
      - Changing the device name
        You can change the device name for your mobile device.
      - Setting the LED brightness
        You can adjust the brightness of your LED on the mobile device.
      - Selecting the IEM audio interface
        You can select the desired audio interface as the signal source for your IEM link.
      - Selecting an audio channel (IEM link)
        You can assign an audio channel number for your IEM link.
      - Activating Focus mode
        You can activate/deactivate Focus mode for your IEM link.
      - Adjusting the balance
        You can change the balance for your IEM link.
      - Setting the volume
        The volume can be controlled directly from the device as well as from the WebUI.
      - Setting the min volume
        You can set a predefined min volume for your IEM link.
      - Setting the max volume
        You can set a predefined max volume for your IEM link.
      - Activating/deactivating cable emulation
        You can emulate the capacitance of connected cables and influence the sound of your mic/line input.
      - Activating/deactivating Low Cut
        You can reduce or remove low frequencies in the audio signal while allowing high frequencies to pass through.
      - Setting the Preamp Gain
        With the preamp you can increase the audio level for your Mic/Line output.
      - Activating/deactivating Test Tone
        With a constant test tone, you can simulate and test the performance of your audio devices in different dB levels.
    - Activating the license
      Under Entitlement, you can enter and activate the current license for the frequency spectrum.
  - Frequency Scan
    You can use an RF scan to examine the current frequency situation of your connected antenna.
  - Audio levels
    Under Audio Levels you can monitor all interfaces at a glance.
  - Audio inputs and outputs
    Here you have an overview of all channels at a glance and can assign the audio network input and output for the link channels directly and easily.
- LinkDesk
  Detailed description of the installation, start-up and operation of the LinkDesk software.

Adding/removing an audio channel (Mic/Line)

You can assign an audio channel number and the interface output for your Mic/Line link.

You can route audio links to several channels. Routing can be performed easily via the routing matrix (see Audio inputs and outputs).

To add an audio channel:

In the top bar, navigate to Configuration > Mobile Devices > Mic Settings.
Select the channel number from the drop-down list Channel which is indicated with a plus in front of it (e.g. +1).

To remove the link channel:

Select the channel number from the drop-down list Channel which is indicated with a minus in front of it (e.g. -1).

To select the output interface of the assigned link channel:

Activate/deactivate the check-boxes under D (for DANTE®), M1 (for MADI 1) and/or M2 (for MADI 2).

The audio channel and the audio interface output has been added/removed.