Home
Instruction manual
Starting up and operating devices of the Evolution Wireless Digital series.
EW-DX EM 2 rack receiver
Setting options in the menu
In the receiver menu, you can configure the following settings.
Ch 1 / Ch 2 -> Trim menu item
In the Trim menu item, you can adjust the audio level of the received transmitter to input signals of different volumes.

Instruction manual
Starting up and operating devices of the Evolution Wireless Digital series.
- EW-D EM rack receiver
- EW-D SKM-S handheld transmitter
- EW-D SK bodypack transmitter
- EW-DX EM 2 rack receiver
  - Product overview
  - Connecting/disconnecting the receiver to/from the power supply system
  - Connecting receivers in a network
  - Connecting antennas
  - Outputting audio signals
  - Installing receivers in a rack
    Observe the following instructions when mounting the receiver in a rack.
  - Switching the receiver on and off
  - Lock-off function
  - Using the headphone output
    You can use the headphone output on the front of the receiver (6.3 mm jack) to listen to the audio signals of the two channels.
  - Meaning of the LEDs
  - Displays on the receiver’s display panel
    Status information such as frequency, reception quality, battery status and audio level is shown on the display.
  - Buttons for navigating the menu
  - Opening the menu and navigating the menu items
  - Menu structure
    The figure shows the complete menu structure in an overview.
  - Setting options in the menu
    In the receiver menu, you can configure the following settings.
    - Ch 1 / Ch 2 -> Name menu item
      In the Name menu item, you can define the name of the link for the channel in question.
    - Ch 1 / Ch 2 -> Frequency menu item
      In the Frequency menu item, you can adjust the frequency for the channel in question.
    - Ch 1 / Ch 2 -> Gain menu item
      Under the Gain menu item, you can set the audio level of the audio signal coming from the received transmitter (e.g. vocals or speech via EW-DX SKM or guitar via EW-DX SK).
    - Ch 1 / Ch 2 -> AF Out menu item
      In the AF Out menu item, you can set the audio level that is output via the audio outputs of the particular receiving channel.
    - Ch 1 / Ch 2 -> Trim menu item
      In the Trim menu item, you can adjust the audio level of the received transmitter to input signals of different volumes.
    - Ch 1 / Ch 2 -> Low Cut menu item
      In the Low Cut menu item, you can set the value of the low cut filter for the respective channel.
    - Ch 1 / Ch 2 -> Cable Emul. menu item
      In the Cable Emul. menu item, you can emulate instrument cable lengths:
    - Ch 1 / Ch 2 -> Mute Mode menu item
      In the Mute Mode menu item, you can set the function of the mute switch on the connected transmitter (EW-DX SK, EW-DX SK 3-PIN, EW-DX SKM-S, EW-DX TS).
    - Ch 1 / Ch 2 -> Auto Lock menu item
      In the Auto Lock menu item, you can activate or deactivate the lock-off for the received transmitter.
    - Ch 1 / Ch 2 -> LED menu item
      The LED menu item allows you to set the behavior of the LINK LED on the received transmitter.
    - Ch 1 / Ch 2 -> Sync Parameters menu item
      In the Sync Parameters menu item, you can choose which settings for the transmitter you want to transfer from the receiver to the transmitter during the synchronization.
    - Ch 1 / Ch 2 -> Scan / Auto Setup menu item
    - Ch 1 / Ch 2 -> Walktest menu item
      The Walktest menu item allows the performance of a reception test.
    - Ch 1 / Ch 2 -> TX Software menu item
      The TX Software menu item displays the software version of the received transmitter.
  - System menu item
  - Updating the firmware of the receiver
    You can update the receiver firmware using the Sennheiser Control Cockpit software, the Wireless Systems Manager software or the Smart Assist app.
- EW-DX EM 2 Dante rack receiver
- EW-DX EM 4 Dante rack receiver
- EW-DX SKM | EW-DX SKM-S handheld transmitter
- EW-DX SK | EW-DX SK 3-PIN bodypack transmitter
- Table stand EW-DX TS 3-pin | EW-DX TS 5-pin
- EW-DP EK portable receiver
- EW-DP SKP plug-on transmitter
- Establishing a radio link | Synchronizing the receiver and transmitter
- L 70 USB charger
- CHG 70N-C charger
  The CHG 70N-C is a network enabled charger featuring two individual charging bays.
- EW-D ASA antenna splitter
- AWM active directional antenna
- Cleaning and maintenance
  Note the following information when cleaning and maintaining products of the Evolution Wireless Digital series.

Ch 1 / Ch 2 -> Trim menu item

In the Trim menu item, you can adjust the audio level of the received transmitter to input signals of different volumes.

For example, if you are using multiple transmitters in alternation for a single receiving channel, you can adjust the transmitters to the different input signals using the trim setting. You do not need to change the channel’s gain setting.

Setting range: -12 dB to +6 dB in increments of 1 dB

To open the Trim menu item:

In the menu, navigate to the Trim menu item for the desired channel.
Press the jog dial to open the menu.
The following view is displayed:
Turn the jog dial to set the desired value.
Press the jog dial to save your setting.
Or
Press the ESC button to cancel the entry without saving the settings.

For the set value to be applied to the received transmitter, you must synchronize the channel (Connecting to the EW-DX EM receivers / synchronizing the EW-DX EM).