Home
Instruction manual
Starting up and operating devices of the Digital 6000 line.
SK 6000 bodypack transmitter
These sections contain information about installing, starting up and operating the SK 6000 bodypack transmitter.
Operating the menu of the SK 6000 bodypack transmitter
Navigating through the menu and making changes.

Instruction manual
Starting up and operating devices of the Digital 6000 line.
- EM 6000 2-channel receiver
  These sections contain information about installing, starting up and operating the EM 6000 2-channel receiver.
- SKM 6000 handheld transmitter
  These sections contain information about installing, starting up and operating the SKM 6000 handheld transmitter.
- SK 6000 bodypack transmitter
  These sections contain information about installing, starting up and operating the SK 6000 bodypack transmitter.
  - Product overview
  - Inserting and removing the BA 61 rechargeable battery
  - Inserting and removing the B 61 battery compartment
  - Mounting the antenna
  - Connecting a microphone
  - Connecting an instrument or line source
    You can connect instruments or audio sources with a line level to the SK 6000 bodypack transmitter.
  - Connecting a command adapter
  - Switching the SK 6000 on and off
  - Displays on the SK 6000 bodypack transmitter display panel
    You can view the following information on the transmitter display.
  - Operating the menu of the SK 6000 bodypack transmitter
    Navigating through the menu and making changes.
    - Tune menu item
      In this menu item, you can adjust a frequency in 25 kHz steps.
    - Preset menu item
      This menu item displays the frequency preset U together with its corresponding frequency.
    - Name menu item
      In this menu item, you can set a freely selectable name for the transmitter.
    - Gain menu item
      In this menu item, you can adjust the input gain in 3 dB steps.
    - Low Cut menu item
      In this menu item, you can adjust the value for the low cut filter.
    - Display menu item
      In this menu item, you can choose whether the home screen on the transmitter display shows the set frequency, the frequency preset, or the name of the transmitter or radio link.
    - Lock menu item
      In this menu item, you can activate or deactivate the lock-off for the transmitter.
    - Test Tone menu item
      In this menu item, you can activate a 1 kHz test tone that the transmitter transmits instead of the input signal.
    - LED Mode menu item
      In this menu item, you can set the behavior of the blue LED in the ON/OFF/ESC button.
    - Reset menu item
      In this menu item, you can reset the transmitter settings to the factory settings.
    - Information menu item
      In this menu item, you can display the installed firmware version and the overall frequency range for the transmitter.
  - Operating the SK 6000 with a command adapter
    You can use the command adapter to switch the audio channel on the EM 6000 receiver via remote control.
  - Updating the transmitter firmware
- SK 6212 bodypack transmitter
  These sections contain information about installing, starting up and operating the SK 6212 bodypack transmitter.
- Modular L 6000 charger
  These sections contain information about installing, starting up and operating the modular L 6000 charger and the corresponding charging modules.
- L 70 USB charger
- Establishing a radio link
  Note the following points when you establish a radio link between the transmitter and receiver.
- Synchronizing devices
- Cleaning and maintenance
  Note the following information when cleaning and maintaining Digital 6000 series products.

Operating the menu of the SK 6000 bodypack transmitter

Navigating through the menu and making changes.

Product overview

To open the menu:

Press the SET button.
The operating menu is shown on the transmitter display panel.
Press the UP or DOWN buttons to navigate through the individual menu items.
Press the SET button to open the selected menu item.

After you open a menu item, you can make changes as follows:

Press the UP or DOWN buttons to set the displayed value.
Press the SET button to save the setting.
Press the ESC (ON/OFF) button to leave the menu item without saving the setting.