Home
Instruction manual
Starting up and operating devices of the Digital 6000 line.
SKM 6000 handheld transmitter
These sections contain information about installing, starting up and operating the SKM 6000 handheld transmitter.
Operating the menu of the SKM 6000 handheld transmitter
Navigating through the menu and making changes.
Lock menu item
In this menu item, you can activate or deactivate the lock-off for the transmitter.

Instruction manual
Starting up and operating devices of the Digital 6000 line.
- EM 6000 2-channel receiver
  These sections contain information about installing, starting up and operating the EM 6000 2-channel receiver.
- SKM 6000 handheld transmitter
  These sections contain information about installing, starting up and operating the SKM 6000 handheld transmitter.
  - Product overview
  - Inserting and removing the BA 60 rechargeable battery
  - Inserting and removing the B 60 battery compartment
  - Replacing the microphone module
  - Switching the SKM 6000 on and off
  - Displays on the SKM 6000 handheld transmitter display panel
    You can view the following information on the transmitter display.
  - Operating the menu of the SKM 6000 handheld transmitter
    Navigating through the menu and making changes.
    - Tune menu item
      In this menu item, you can adjust a frequency in 25 kHz steps.
    - Preset menu item
      This menu item displays the frequency preset U together with its corresponding frequency.
    - Name menu item
      In this menu item, you can set a freely selectable name for the transmitter.
    - Gain menu item
      In this menu item, you can adjust the input gain in 3 dB steps.
    - Low Cut menu item
      In this menu item, you can adjust the value for the low cut filter.
    - Display menu item
      In this menu item, you can choose whether the home screen on the transmitter display shows the set frequency, the frequency preset, or the name of the transmitter or radio link.
    - Lock menu item
      In this menu item, you can activate or deactivate the lock-off for the transmitter.
    - Test Tone menu item
      In this menu item, you can activate a 1 kHz test tone that the transmitter transmits instead of the input signal.
    - LED Mode menu item
      In this menu item, you can set the behavior of the blue LED in the ON/OFF/ESC button.
    - Reset menu item
      In this menu item, you can reset the transmitter settings to the factory settings.
    - Information menu item
      In this menu item, you can display the installed firmware version and the overall frequency range for the transmitter.
  - Updating the transmitter firmware
- SK 6000 bodypack transmitter
  These sections contain information about installing, starting up and operating the SK 6000 bodypack transmitter.
- SK 6212 bodypack transmitter
  These sections contain information about installing, starting up and operating the SK 6212 bodypack transmitter.
- Modular L 6000 charger
  These sections contain information about installing, starting up and operating the modular L 6000 charger and the corresponding charging modules.
- L 70 USB charger
- Establishing a radio link
  Note the following points when you establish a radio link between the transmitter and receiver.
- Synchronizing devices
- Cleaning and maintenance
  Note the following information when cleaning and maintaining Digital 6000 series products.

Lock menu item

In this menu item, you can activate or deactivate the lock-off for the transmitter.

To enable the lock-off:

Open the Lock menu item and set the value to On.
Save your entry by pressing the SET button.
The automatic lock-off function will remain activated.

To temporarily deactivate the lock function:

Press the ON/OFF/ESC button.
The message LOCKED is shown on the display.
Press the UP or DOWN button.
The message UNLOCK is shown on the display.
Press the SET button.
The lock-off function is now temporarily disabled.
You can change settings as needed in the menu. The lock-off function is reactivated after 10 seconds of inactivity.

To disable the lock-off:

Open the Lock menu item and set the value to Off.
Save your entry by pressing the SET button.
The automatic lock-off function will remain disabled.