Home
User manual
Detailed description of the start-up and operation of your selected hardware and software product.
LinkDesk
Detailed description of the installation, start-up and operation of the LinkDesk software.
Base Station
The Base Station is the central hardware for managing and monitoring all compatible Spectera products.
Pairing/unpairing mobile devices
In LinkDesk you can pair up to 128 mobile devices to a Base Station within one RF channel.

User manual
Detailed description of the start-up and operation of your selected hardware and software product.
- Network & Security Guide
  This document is intended for IT administrators, system integrators and event technicians and serves as an planning and configuration guide for integrating components of the Spectera offering into diverse network environments from small home networks up to enterprise networks.
- Spectera
  Detailed description of the start-up and operation of your selected hardware.
- WebUI
  Detailed description of the WebUI navigation and configuration.
- LinkDesk
  Detailed description of the installation, start-up and operation of the LinkDesk software.
  - Get started
  - Basic configuration
    Start your basic configuration with the recommended steps.
  - Productions
    In this chapter you will learn the basic information about productions.
  - Base Station
    The Base Station is the central hardware for managing and monitoring all compatible Spectera products.
    - Identifying Base Stations
      You can remotely identify your Base Station.
    - Adding Base Stations
      The networked Base Station can be added to the software using an IP address.
    - Activating license
      Here you will learn how to activate your region-specific license for your Base Station.
    - Activating antennas
      Antennas connected to a Base Station must be selected and activated before use.
    - Adding RF channels
      You can configure an RF channel and assign it to the available devices.
    - Configuring RF channels
      You can adjust the RF channel in its antenna selection, frequency and bandwidth.
    - Scanning RF spectrum
      You can use an RF scan to examine the current frequency situation of your connected antenna.
    - Adding mobile devices
      You can add mobile devices to your connected Base Station.
    - Pairing/unpairing mobile devices
      In LinkDesk you can pair up to 128 mobile devices to a Base Station within one RF channel.
    - Displaying device information
      You can display detailed information relating to your Spectera device.
    - Changing device name
      You can change the device name for your Base Station.
    - Configuring interface settings
      You can configure the interfaces of the inputs and outputs on the device individually.
    - Muting/unmuting RF signals
      You can mute/unmute the RF signals of the configured channels.
    - Resetting RF channels
      You can reset or remove you configured RF channel from the current production.
    - Resetting device password
      You can reset the assigned device password on your Base Station to its factory settings.
    - Removing Base Station
      You can delete your configured Base Station from the current production.
    - Updating firmware (Base Station)
      The firmware version of the Base Station can be downloaded and updated manually.
  - Mobile devices
  - Routing Editor
    The editor serves as a basic configurator for mobile devices and also provides an overview of all connected devices with their total capacity utilization within an RF spectrum.
  - Error handling
    Summary of the typical error messages that can occur and how to resolve them.

Pairing/unpairing mobile devices

In LinkDesk you can pair up to 128 mobile devices to a Base Station within one RF channel.

Mobile devices can only be paired and operated with one Base Station at a time. If a mobile device is to be used with another Base Station, it must first be paired again.

Please unmute at least one RF channel before pairing if this was not done automatically!

Mobile device cards cannot be re-ordered. Please add devices in the desired order. Newly added devices are always added at last position to the right.

To pair a mobile device:

In your production card, activate the function DEVICE SYNCHRONIZATION on the left-hand side of the top bar.
Click on the button MD Manager on the left-hand side of the top bar.
A new window Add mobile devices opens.
Select your Base Station from the drop down list on the left-hand side and activate the PAIRING MODE.
Switch on your mobile device and activate the Pairing Mode if it has not been activated automatically (Switching the SEK on and off).
After a few seconds, the available mobile devices are displayed in the list.
Click on the button in the line of the mobile device to be paired.
A confirmation code is displayed both in LinkDesk and on the mobile device.
Compare the displayed code at both endpoints.
In LinkDesk, click on Confirm to pair the selected mobile device.
The mobile device has been paired successfully. The device state color changes to:
- green: successful operation, or
- yellow: warning (e. g. if the audio links have not yet been assigned (see also Device State Colors)).

To unpair a mobile device:

You can either
- click on the unpair button of the corresponding device in the MD Manager or
- click on the three dots of the mobile device card and select the unpair function.
The mobile device has been unpaired successfully.

The mobile devices have been successfully paired/unpaired.